Correct drainage pipes - that's how it works

Correct drainage pipes - that's how it works: pipes

Musty or unpleasant odors and traces of water in the kitchen cabinet or on the bathroom floor?

These are typical warning signs that a drainpipe may have leaked. Such an indication, you must go to the bottom, because apart from the evil channel smell threatening too Damage to the kitchen cabinets and bathroom furniture or in the worst case mold.

Usually the complete waste set or individual pipe segments can easily be exchanged in case of damage. The material is not expensive either.

But what to do if, due to the weekend or a holiday, the DIY stores are closed or the installer does not have time immediately? Then First seal the pipe temporarily yourselfso that the leak is closed for at least a few days.

You can read here how it works. You first have to find out which pipe material it is. Old metal drainpipes were made of lead or iron, rarely copper. Modern plastic pipes consist of PVC, ABS or PE. Depending on the material, follow the instructions.

Metal pipes of lead, iron or copper

Take a close look at the damaged area and, above all, the extent of the damage. Leaves little water, then the pipe is only damp in places or only small water droplets form. In this case, a clay from two-component epoxy resin adhesive helps.

Correct drainage pipes - that's how it works: works

Metal pipes, here partly made of cast iron, partly of copper, are found less frequently in the kitchen and bathroom directly, but rather in the further course of the sewage system.

Major damagefrom which it drips steadily or even trickles, can be sealed with home remedies barely correct. Here only helps the swift exchange. You can then also with the plasticine makeshift seal and should In any case, put a container under the leakuntil a repair is possible.

Material and aids

  • Two-component epoxy modeling clay
  • Thin rubber gloves

Seal metal pipes

First make sure that there is no water in the pipe and that none of it runs after it.

Tip: It is best to tap the associated faucet with tape and attach a note to it. No one will turn on the water if you temporarily leave the room during the repair.

Now wipe the licking spot thoroughly clean, until they free from water, dust or other residues is, otherwise the mass does not stick to the pipe. Wear rubber gloves when working with the epoxy.

Correct drainage pipes - that's how it works: drainage

As long as plastic pipes - here made of PVC - have not been damaged by mechanical influences, leaks are usually found near connections and connections.

Cut a not-too-small piece off the putty strand and knead thoroughly until the two components are completely mixed. The clay then shows a uniform, homogeneous color. Please also read the manufacturer's manual.

Form a sausage-shaped strand from the mass and place it around the damaged pipe like a bandage around the pipe. Then carefully press the clay to airtight - there must be no gaps or holes. The plasticine must now harden according to the manufacturer's instructions. That can be done without further ado 24 hours last - during this time no water may flow through the pipe.

After curing Let water run on a trial basis and see if it leaks out. If you are not sure, wrap a piece of kitchen paper around the repair area - you can then see traces of water on the paper. Normally, everything would have to be tight until the final repair.

Plastic pipes made of PVC or ABS

For these tubes, it is recommended to use a patch or one repair sleeve to stick to the leak. This is feasible with budget funds.

Material and tools

  • acetone
  • Thin rubber gloves
  • Fast-curing 2-component acrylate adhesive
  • Non-elastic gauze bandage (from the first-aid kit)
  • flat brush

Seal plastic pipes

Also in this case allowed in the pipe no water and no running water.If this is the case, thoroughly clean the tube with acetone around the damaged area. The plastic must then be completely dry, clean, free of oil and grease.Since you do not have much time to process the glue, you should now prepare all the other materials and tools you need.

The acrylate usually consists of one powdered hardener and one liquid binder. Put the complete powder in a beaker and then add the binder resin complete added. Mix both components with the spatula thoroughly to a homogeneous adhesive by. Now you have about 10 mins Time for the repair.

Correct drainage pipes - that's how it works: works

Tip: A quick alternative, with which even flexible drain and inlet pipes can be sealed, are self-welding repair tapes.

Wear with the flat brush Adhesive in width of the gauze bandage around the damaged area. Now wrap the tube at this point a total of ten times smooth and tight with the bandage and apply after every second winding glue again on the repair site. Finally, cut off the rest of the bandage and fix the tail with glue.

Is that lying Leak near a fitting or sleeve, seal it off with. To do this, apply adhesive about half the width of the bandage, wrap the gauze strip four times, while applying glue again on every other layer, and then wind it back onto the tube.

Here is wound a few times - again with an intermediate order of the adhesive -, then it goes back to the sleeve or the fitting and then after a few windings again on the pipe. There apply a few layers of gauze, as described, and glue the end of the gauze bandage.

The repair must now cure for about 10 hours, Then the glue is tight and you can put the drain back into operation. After a curing time of 24 hours In an emergency, even lines with a pressure of up to 16 bar be put into operation. But check them regularly and put them to rest, say overnight, the best - the improvised gasket is not intended as a permanent solution.

By the way: The more precisely the mixing ratio of binder and hardener prescribed by the manufacturer is adhered to, the more secure the adhesive will stick. Since the mixture is slightly inaccurate by weight for small quantities, we recommend a complete package approach, as this excludes this source of error.

Plastic pipes made of PE, HDPE or PP

The bad news right away: Polyethylene, high density polyethylene or polypropylene can be used do not stick, The materials can not be wetted because of their chemical and physical properties, so the usual adhesives simply do not adhere.

Therefore, a quick repair is hardly possible, the pipe in question must In any case be exchanged soon. Until then, you should shut down the relevant drain line and the associated inlet. Set for all cases collecting vessel under the leak, inform all family members and attach a warningthat the associated faucet must not be opened.

Similar sites

  • Seal flat roof
  • Clean the drain properly
  • Plastic pipes for plumbing - Plastic plumbing at a glance
  • Repair gutter - seal copper gutter and zinc gutter
  • Lay tiles correctly
  • PVC: polyvinyl chloride as floor covering
  • Awning repair - that's how it works
  • Make distilled water yourself
  • Laying large tiles - this is how it works
  • Seal bottom plate
  • Seal the shower - protect the walls from splashes of water
  • Seal cellar: seal cellar from inside and outside and insulate
  • Cooking Easter Eggs: That's right
  • Hang and arrange pictures properly

Video Board: The IPGC Drainage Pipe