Set the heating thermostat correctly - Tips for do-it-yourselfers

Set the heating thermostat correctly - Tips for do-it-yourselfers: tips

In the heating regulation plays the operation and adjustment of the radiator thermostat play a significant role, With its help, not only can the temperature be turned up and down, but also consciously save energy. Therefore, it is important to understand how a thermostatic head works. But more importantly, how should it be adjusted and mounted to regulate the desired cozy warmth?

Sometimes it can happen that even a thermostatic head fails its service and must be replaced. This is annoying, but no reason to panic: Since the head is not integrated into the pipe system, it can be easily replaced without having to drain water from the heater. For this are No special tools or an installer needed, It is important, however, to pay attention to the correct transition thread.

Below we explain How to correctly set a heating thermostat yourself.

The optimal setting for saving energy

Generally recommended a room temperature of around 20° C in the living area. This number of degrees is achieved with regulator level 3 on the radiator thermostat. This level should then stay as day and night as possible, because the constant adjustment leads to a waste of energy.

Only during prolonged absence, for example during vacation, should the heater is turned down to the regulator level 1, to ensure a room temperature of 12° C and to prevent mold growth.

Mechanical thermostats

Set the heating thermostat correctly - Tips for do-it-yourselfers: heating

Mechanical radiator thermostat

Many heaters will be operated with so-called mechanical thermostats, which are to be adjusted by hand. They are composed of three basic components: these include the spring-loaded valve with pin, the housing and the temperature sensor.

The pen regulates, How much water can flow through the radiator. If the thermostat is turned to the right, the valve pin is pressed in more, which reduces the valve opening. As a result, less water can flow through, whereby the heat output is lowered.

Using the thermostat integrated temperature sensor The heater will automatically increase or decrease its output if there are temperature differences.

Loosen the clamping pin

Should Problems with the control of the thermostatic head home improvement can easily unscrew the thermostat, because the cause is often due to a pin that ensures that the heating is permanently set to zero. This can be carefully pulled out with pliers again. However, it is better to lightly tap the case with a rubber mallet to loosen the pin.

Many other interesting topics around the topic heating control can be found on kesselheld.de.

Screw on thermostat and put on

When screwing should the thermostatic head to the highest control level - in this case to five - because it can be removed easily at elevated temperature control and the pressure is reduced. Then loosen the ring or clamp with a pair of pliers or a screwdriver. It is located directly behind the thermostat. Especially with older heaters, the screw ring can be loose, so that it can be removed together with the thermostatic head by hand and that by turning slightly. The thermostat is now turned up to the stop and put on the pin on the radiator or turned into the thread. In doing so, the later adjustment markings should be pointing upwards accordingly.

Electronic thermostats

Set the heating thermostat correctly - Tips for do-it-yourselfers: correctly

Radiator thermostats ensure a comfortable temperature

Nowadays you can on the market also electronic thermostats find. These prove to be advantageous because they increase living comfort by means of an even more exact adaptation of the desired temperature than is already the case with mechanical thermostats. They can be pre-programmed with specific setpoint temperature values ​​and regulate the heat output automatically.

Also on the go can be adjust the heating via apps or tablets much more needs-oriented. Do-it-yourselfers and homeowners who want to heat particularly energy-efficient and cost-saving, should think about the purchase of an electronic thermostat and exchange or retrofit. This can be done independently with a few simple steps.

Replace thermostatic head

After the old thermostatic head has been unscrewed, an adapter pushed onto the valve, which you get when you buy an electronic thermostat. Afterwards, turn the adjusting wheel on the valve attachment counterclockwise completely. Now, if the valve attachment is attached to the adapter, the assembly is completed. Subsequently, valve and control center correspond with radio signals. Before that, however, the temperature data at the control panel must be entered and the batteries inserted into the thermostat.

Similar sites

  • Sustainability: home improvement tips for sustainable living
  • Paint ceilings and walls correctly
  • Tips for drilling metal and steel
  • CNC milling machine for the home improvement
  • Adjust slatted frame
  • Save money with DIY and DIY
  • Instructions: set your own window
  • Adjusting the door: adjusting the doors made easy
  • Replace radiator
  • Money saving tips for home improvement
  • Hang and arrange pictures properly
  • Soldering iron test and price comparison: soldering iron, gas soldering iron and battery soldering iron in
  • Instructions and tips for proper wallpapering
  • Conservatory: heating and ventilation
  • Defrost the freezer properly

Video Board: How to Replace an Old Thermostat -- by Home Repair Tutor