Laying plan for tiles - symmetry when laying tiles

Laying plan for tiles - symmetry when laying tiles: symmetry

Are the selected tiles and pretreated the substrate, it goes to the installation plan.

The measure of all things in tiled surfaces are symmetry and straightness. Because only then can one harmoniously balanced distribution of space achieve.

Whether straight wall, wall edge or pillar, niche or projection: There are practicable solutions for every local specialty.

Even a large area or a continuous joint course in adjacent rooms are no problem for do-it-yourselfers however, keep an eye on the symmetry, so that you get a nice and above all straight result at the end.

Especially at the Development of a layout plan requires care and accuracyFinally, it serves as a template during the work. Similarly, good planning can significantly reduce waste.

Tool for tiling walls and floors

For a smooth process you should provide the following devices:

  • agitator
  • Bricklayer and notched trowel
  • Tile cutter (angle grinder)
  • hole cutters
  • Spirit level or cross line laser
  • Straight edge or aluminum rail
  • tile spacers

Furthermore There are also other aids that facilitate the work, but especially for laying tiles have to be bought.

These include the Parrot beak and tiling tongs, tile hammer or tiling corners.

With the right tools even corners and edges, doors and shelves, water and electrical installations are no problem. Detailed information on the application can be found on the tile laying tool.

Borders and colored tiles

Laying plan for tiles - symmetry when laying tiles: laying

Accents through colored borders and tiles

Become mainly Processed monochrome tiles, a larger wall can quickly become dreary and boring Act. Remedy borders or colored tiles. These can be set as a conclusion or in several rows.

Especially very high rooms can be optically adjusted. Even different colored tiles can set atmospheric accents. As a simple options, the offer Replacement of individual tiles, adhesive foils or a paint job to the tiles.

A special effect is also with single ornaments and decorations on tiles generated.

These can be well also subsequently dthe overall picture and the decoration of the bathroom to adjust, However, it should not be overdone. Often, less is more and, above all, more appealing.

Uniform joint picture

Laying plan for tiles - symmetry when laying tiles: laying

Uniform joint between floor and wall

Since the Tiles the joints are always visible and often even a contrast to the tiles should form the entire joint pattern uniform. In addition to even joints, transitions between wall and floor or to other rooms are important.

Transition from the ground to the wall

If the decision for Floor and wall on the same tile size, should also be adjusted to the joints and be consistent. This means that the joints of the wall meet exactly the joints of the floor tiles.

If a different tile size is selected, it is advantageous to use a double size to Every second fugue is synchronized allow. If the tiles are very large and the wall gets very few joints, the grout picture does not need to be given so much attention.

Transition between two rooms

Laying plan for tiles - symmetry when laying tiles: tiles

Uniform joint pattern between two rooms

If floor tiles are laid in two rooms, a uniform joint pattern must also be taken into account here. Even at an existing door sill, results in the same installation a more uniform and quiet overall picture.

When laying elongated tiles, it should be up be avoided in any case, different installation directions to choose.

However, a uniform joint pattern does not mean that it must not be interrupted. at Cross-spatial tiling should not be dispensed with an expansion joint become.

Temperature fluctuations and thus Associated movements and tensions can cause tearing and ruin the overall picture. The replacement of individual tiles is possible, but expensive.

Avoid cut edges

Laying plan for tiles - symmetry when laying tiles: plan

Avoid cut edges

An important question when laying tiles is "Where do I start and where do I cut?" This is pretty easy to answer with three basic rules.

  1. If possible, avoid cutting tiles.
  2. Always start outwards with an uncut tile.
  3. Always pay attention to the symmetry.

Specifically, that means that projecting corners, such as chimneys or ledges always started with a full tile at the front edge become.

The Cut edges then end in the inner corners and are covered by the silicone joint. The new area is again started with the cut off remainder.

That's how it is on the one hand no waste and for another form both pieces optically again a tile and unify the joint picture.

Cut the tile mirror correctly

Laying plan for tiles - symmetry when laying tiles: tiles

Cut the tile mirror correctly

If the height of the tile mirror is not well defined, try to tile from the bottom to the top thus avoid cutting tiles.

However, as the first of the entire floor checked become. Is the Soil not straightIt is rarely possible to start anywhere with a non-cut tile.

In such cases, it must be weighed whether it makes sense with to start some complete tiles and the rest to cut or tiled right from the top down and all are cut.

Determine Windows, wall cabinets or roof slopes the upper edge of the tile mirror, all tiles must be cut. In this case is always tiled from top to bottom.

This results in a above uniform tile pattern and the cutting edge of the tiles is down through the silicone joint covered.

10 professional advice for the right tiling

  1. Stress determines the tile material.
  2. Before laying, check the substrate and pretreat if necessary.
  3. The right grout for the substrate is the basis for a firm grip.
  4. Full-surface adhesive application ensures long-term enjoyment of the tiles.
  5. First allow the adhesive to set and then grout.
  6. Symmetry guarantees a successful look.
  7. Cotton cloths help against mortar streaks.
  8. Working in the wet area: first seal and then tiled.
  9. Natural stone remains discoloration free only with suitable products.
  10. Permanently elastic joints on sanitary facilities: The joints are sealed with adhesive tape, smoothing cutter and sanitary silicone.

Similar sites

  • Lay tiles correctly
  • Painting tiles - painting tiles
  • Lay tile on tile
  • Tile grout - instructions
  • Grout mortar - find the right tile grout
  • Simply renovate the garage floor yourself
  • Laying large tiles - this is how it works
  • Borders and borders as wall decorations
  • Porcelain stoneware cutting - tips for handling porcelain stoneware tiles
  • Glue the tiles over
  • Tool for laying tiles
  • Tile stairs properly - you must pay attention
  • Tile cutting

Video Board: Herringbone Installer video