Making lantern out of wood - construction manual for wooden lantern

Building instructions for a wooden lantern

Making lantern out of wood - construction manual for wooden lantern: lantern

When people at St. Martin go through the streets with colorful paper lanterns, they are usually covered with plastic wrap to protect them from rain. This problem does not exist with a wooden lantern, because it is weatherproof and, due to its special design, becomes an eye-catcher for the spectators at the roadside. However, fretwork has yet another advantage: plywood is relatively soft and easy to work with, so children - depending on their age under the guidance of their parents - can tinker with it and glue or paint the lanterns with colored paper.

In addition, this martini lantern is also suitable as a window and table decoration for the Martinsfest. In addition, the self-made wooden decoration does not fade so quickly and can be reused for several years.

How to build a lantern made of wood with the fretsaw, shows this craft instructions with practical tips on priming and design.

Materials for fretwork

When crafting with a fretsaw, the wood must not be too thick, otherwise sawing becomes unnecessarily difficult. In particular, when children are to learn how to handle the fretsaw, thinner wood is easier to work with. The following materials are required for crafting a wooden lantern:

  • 4 x plywood, 6 mm (for the sides)
  • 1 x plywood, 8-10 mm (for the floor)
  • jigsaw
  • Laubsägeblätter
  • sandpaper
  • Countersunk screws (quantity depends on the attachment)
  • Drills or cordless screwdriver
  • clamp
  • Colorful transparent paper
  • scissors
  • pencil
  • craft glue
  • wood glue
  • Stable wire
  • Wood primer
  • Acrylics
  • Possibly. 4 x squared timbers or strips
  • Possibly. craft paper
  • Possibly. long fabric or gift ribbon

As an alternative to plywood, thin spruce glulam is also suitable.

For the lantern bar and the lighting:

  • 1 x electric lantern bar

or

  • 1 x roundwood or round rod
  • 1 x stable wire
  • 1 x candle holder with candle

Instructions: Make lantern with a fretsaw

Making lantern out of wood - construction manual for wooden lantern: manual

Lantern floor in several variants

This manual is freely modifiable. For example, if you want to make a wider border or a smaller lantern, you can adjust our jigsaw templates as you like. Our Martinslaterne consists of four identical side panels and a square bottom, The base has the dimensions 20 cm x 20 cm. Depending on the desired size of the lantern, the height of the side panels can be varied. The important thing is that their base has the same width as the floor.

Then transfer the specified dimensions for the floor and side panels to the wood. With a screw clamp, the board is fixed on the table, so it does not wobble during the fretwork.

Saw out the bottom and lantern sides

In the next step follows Clamping the fretsaw blade, When children tinker, parents provide a little help, because the sheet must be clamped straight and tight, otherwise it tears. Tip: To clamp the sheet quicklyPlace the jigsaw between your knees and gently squeeze the ends together. Now you can simply insert the saw blade into the clamps. Then the screws are tightened.

Finally, you saw off the individual parts of the lantern. It may be necessary to loosen the screw clamp to move the board. After that, the edges become thorough smoothed with emery paper, Now you drill on two opposite lantern sides Hole for the suspension, Once the lantern is assembled, the wire is pushed through and attached to the rod.

Making lantern out of wood - construction manual for wooden lantern: making

Design drawing for different side parts

Saw out the window

In the next step, drill a hole near the inner edge of the lantern side with a drill or cordless screwdriver, before threading the saw blade through the hole and tensioning it into the jigsaw. Now saw out the inner area of ​​the window. This area will later be decorated with paper, foil or other crafting materials.

As soon as the first side part of the wooden lantern is ready, the windows of the other three sides are machined using the same method and the edges are then smoothed. Finally, you saw off the bottom of the lantern and smoothed its edges. If you like, you can vary the sides and saw off several smaller windows. These can be identical squares or angular and round shapes of different sizes. In this way, individual lanterns are created with little effort.

Priming and shaping the lantern

After sawing it is advisable to treat all parts with a deep background. The primer seals the pores in the wood surface, protecting it from moisture. In addition, the color covers better. Alternatively, white or gray acrylic paint is used. If the grain remains visible, a glaze is recommended.

After the primer has dried, the design begins: First, paint the individual parts with acrylic paints and let them dry for about 12 hours. Then the colored paper is placed on the lantern side and cut off the overhanging remains. Coat the inner edge with craft or all-purpose glue and press down the tracing paper. After a few minutes the glue has dried. There are also further design possibilities for the Martinslaterne: For example, you can paint white tracing paper or stick with small motifs of colored paper. If you prefer a simple lantern, you use crafting foil, which is attached to the inside.

Making lantern out of wood - construction manual for wooden lantern: wooden

Screw side panels to ground

Assemble wooden lantern

For the attachment of the individual parts is a combination of screws and gluing. For this purpose, you drill each first two small holes in each edge of the soil and then carries one conventional wood glue on the connection points. If children tinker, a solvent-free glue is recommended. Thereafter, the first side part is pressed firmly and clamped for at least 20 minutes in a screw clamp. The setting time depends on the manufacturer. Excess glue should be removed with a cloth. Only then are the two countersunk screwed. Their head shape allows them to sink unobtrusively. - In contrast to round head screws, where the head remains visible. Glue and screw on the remaining side parts in the same way.

Another option is squared timbers and strips. These should be made of a thicker wood than the lantern sides. In both methods, the edge height of the lantern pages should be chosen so that the woods are below the window opening. The four Afford first fasten on the floor and screw on the side parts to them.

Making lantern out of wood - construction manual for wooden lantern: manual

Assembly of the lantern sides on the ground and with ledges and angles

Following a similar principle, the assembly works withfour squared timbersThese are trimmed in the shape of a right triangle and screwed to the floor from the bottom in each corner. Then fix the side panels with one screw per edge.

If you want, build an eyecatcher and binds the side parts together in a band, z. B. with a fabric or gift ribbon. To do this, first drill holes in the left and right frames on each side panel. Important, the holes of the lantern sides must be at the same height. Now a ribbon is threaded through two adjacent holes and knotted together on the inside of the lantern. You can also tie decorative bows on the outside or zigzag the strings like laces through the holes. Supernatant residues are cut off. This way all lantern pages can be connected in a decorative way. However, the band can not replace the screws.

Fix the lantern

In the final step, the wire is pushed through the drilled holes on the upper edge of the lantern and the ends are twisted. Now this handle can be easily hung in the suspension of the electric rod. Done is the wooden lantern.

A good alternative to an electric rod logs or bars. For the suspension, drill a hole through the end of the rod and attach a second wire to it. From its end form a tight loop on which the lantern is hung.

Should one candle illuminate them, attach them with a special candle holder for lanterns, which is available in the craft shop. Attention, with real candles must be sufficient distance to the walls, otherwise ignites the paper. Alternatively, there are LED lights that flicker like real candles. These are especially suitable for children.

Similar sites

  • Tinker angels made of paper and wool
  • Jigsaw templates
  • Making Kites: Instructions for Kites, Eddy and Hexagon Kites
  • Tinker with paper, scissors and glue
  • Tinker folding cards
  • Tinker with wood
  • Make games, toys and decoration out of paper
  • Make butterfly - butterflies made of felt, paper and artwork
  • Tinker Advent Calendar - Free Christmas Calendar Templates
  • Gartenmöbel Bauplan-Archiv: Garden table, garden lounger, garden bench or porch swing to build yourself
  • Tinkering for the beginning of school and school enrollment
  • Tinker cardboard lantern
  • Folding figures, cars, paper plants and crafts
  • Tinker and sew easter bunnies - pattern and print template

Video Board: Building A Cherry And Ebony Wood Lantern