Build a mud table with a gully


material list

For two stands:

  • All weather wooden boards 21 mm, 500 x 120 mm, 6 pieces
  • All-weather wooden strips 35 mm, 340 x 55 mm, 4 pieces
  • All-weather wood squared timbers 70 mm, 1,000 x 70 mm, 2 pieces
  • Beech or spruce round rods ø 20 mm, 310 mm, 4 pieces
  • Key screws 6 x 80 mm with matching washers, 4 pieces
  • Phillips screws 4.0 x 40 mm, 24 pieces

For two waterways:

  • All weather wooden boards 21 mm, 1,800 x 120 mm, 4 pieces
  • All-weather wooden strips 35 mm, 1,800 x 55 mm, 4 pieces
  • All-weather wooden strips 35 mm, 200 x 55 mm, 8 pieces
  • All-weather wooden strips 35 mm, 170 x 55 mm, 2 pieces
  • Phillips screws 4.0 x 40 mm, approx. 62 pieces
  • Tube construction silicone

For the mud table:

  • Hard foam board 3 mm, 1,000 x 500 mm, 1 piece (9 all-weather boards 21 mm, 550 x 120 mm, 8 pieces
  • All-weather wooden strip 35 mm, 930 x 55 mm, 1 piece
  • All-weather wooden strip 35 mm, 160 x 55 mm, 1 piece
  • All-weather wooden strip 35 mm, 600 x 55 mm, 1 piece
  • All-weather wooden strips 35 mm, 500 x 55 mm, 2 pieces
  • All weather wooden strip 35 mm, 1,000 x 55 mm, 1 piece
  • Phillips screws 4.0 x 40 mm, approx. 58 pieces

For the mortar box:

  • 60-liter mortar box

Tools

  • Cordless Screwdriver
  • 4.5 mm drill
  • 6.5 mm drill
  • Kreuzschlitzbit
  • 20 mm Forstnerbohrer
  • Sandpaper K 180
  • wrench
  • ruler
  • pencil

Note:

When screwing two pieces of wood, the piece of wood through which you first screw always be pre-drilled! For a flush surface, all screw heads should be sunk.

The stand

Build a mud table with a gully: wooden

Build a mud table with a gully: wooden

Drill at a distance of 60 mm Holes with a diameter of 20 mm through the posts (3), as shown in the drawing. If the rods (4) are too heavy to insert, grind them slightly thinner at the tips. Now screw down the base plate (1 + 2), and then sand the edges of all parts smooth with 180 grit sandpaper. With 2 key screws each, connect the post to the base plate from below. Make sure that the 20mm holes point in the same direction as the boards of the base plate (do not forget washers!).

The gullies

Build a mud table with a gully: pieces

Build a mud table with a gully: gully

Now screw the boards (5) with the strips (6, 7 and 8), as shown in the picture. Then sand all edges smooth with 180 grit sandpaper. Then seal the middle joint of the floorboards with construction silicone.

The mud table

Build a mud table with a gully: table

Build a mud table with a gully: pieces

First sand all edges smooth with 180 grit sandpaper. First, screw the corner supports at a right angle. Then connect 2 corner supports each with a 500 mm long cross strut. Tip: If you turn all parts upside down, it is easier! Assemble the individual parts as shown, and first screw the remaining strips to the supports. Then you can screw in the rigid foam board. Finally, reinforce the plate from below with a crossbar.

Similar sites

  • Build your own insect hotel - building instructions
  • Puppet theater build yourself: Puppet theater made of wood
  • Building a pallet bed: construction manual for a bed of pallets
  • Building pallet chairs - construction manual for garden armchairs made of pallets
  • Build garden gate
  • Building instructions: Build colorful children's tables and booths yourself
  • Grind drill - instructions
  • Gartenmöbel Bauplan-Archiv: Garden table, garden lounger, garden bench or porch swing to build yourself
  • Building instructions for birdhouses
  • Build sideboard shelf - blueprint with construction manual
  • Building instructions: Coffee table in beech or colored
  • Building sandbox - construction manual for a sandbox
  • Build window frame as a wall decoration yourself
  • Build your own game tower: Spielhaus construction manual
  • Building play furniture and lamps for the nursery


Video Board: WWE MOVES AT THE WATER PARK