Partition with hatch and ceiling lamp

Kitchen room divider with light ceiling

Partition with hatch and ceiling lamp: hatch

The apartment has long ceased to be according to defined utility rooms, but rather furnished according to individual living needs, The new concepts include a kitchen that is no longer a working space but part of the individual living area.

Accordingly, the change occurs: Furnishings, functionality and good light are of utmost importance today. With plasterboard, recessed lighting and metal profiles, you can quickly build an elegant lighting ceiling. And if you want, the attractive, bright dining area, thanks to a freestanding space element, is the focus of the modern kitchen.

Below is an illustrated step-by-step guide with useful home improvement tips and tricks.

Material list and tool list

Material list light panel

  • 4 corner protection rails, total length 11 m
  • 2 CD profiles, 60 mm, 400 cm long, as a suspension for the supporting profiles
  • 10 CD profiles, 60 mm, 97.5 cm long, as support profiles
  • 4 UW profiles, 50 mm, 182 cm long, for floor and ceiling connection
  • 4 UW profiles, 50 mm, 110 cm long, as a fall for the opening
  • 8 CW profiles, 50 mm, 260 cm long, as stand for the room element
  • 2 CW profiles, 50 mm, 150 cm long, to reinforce the upper and lower lintel
  • Wall finishing profiles, 50 mm, 97.5 cm, for fixing the ceiling sail
  • 10 CD Noniushänger
  • 20 CD cross quick connectors
  • approx. 5 plasterboard moldings, U-shaped, 12.5 mm, width 120 cm, length 100 cm, for ceiling sails
  • 4 plasterboard moldings, U-shaped, 12.5 mm, width 100 cm, length 150 and 190 cm, for room element
  • 2.5 m² plasterboard, 12.5 mm, for room element and front sides
  • Dowel 3.9 x 35 mm with matching screws, suitable for the unfinished floor, ceiling and room wall
  • Drywall screws, length 25 mm, for fixing gypsum boards to the frame construction
  • 3.5 m² mineral wool, 170 mm total thickness
  • Bulkhead sealing tape
  • Joint filler
  • Wall paint or plaster with matching primer for plasterboard
  • 8 recessed spotlights with cables, luster terminals and lamps
  • in each case 2 aluminum angles per vernier hanger in appropriate length
  • Installation glue
  • staples

tool list

  • Telescope scale with integrated spirit level or solder and chalk line
  • spirit level
  • ruler
  • drilling machine
  • Screwdrivers
  • Hole saw attachment
  • shears
  • sheet metal tongs
  • Crimperzange *
  • Cutter or carpet knife
  • edge planing
  • stapler
  • spatula
  • abrasive paper
  • Roll for paint or plaster

* The crimping tool is a punching and punching machine Notching tongs for profile connectionIt pierces the overlapping profiles at the same time and thereby ensures a positive connection between the two profiles without further fastening means. They get them in Building materials or tool trade for about 80 €.

building instructions

Floor plan, front view and side view

Here you see one detailed floor plan, with a schematic side view and a schematic front viewwith which you can also convert and adapt the dimensions for the room divider and the ceiling light to your room conditions.

ground plan

Partition with hatch and ceiling lamp: hatch

Floor plan - view from above

sideview

Partition with hatch and ceiling lamp: hatch

Side view on the room divider

front view

Partition with hatch and ceiling lamp: profiles

Front view from the dining room to the kitchen

Room element - from the stud to the planking

Partition with hatch and ceiling lamp: hatch

Step 1

Partition with hatch and ceiling lamp: ceiling

step 2
  1. The alternative to Lot and chalk line is a telescope scale with integrated spirit level, Tensioned between the ceiling and the floor and aligned with the spirit level, the end points of the ceiling and floor rail, the UW profiles, for the double column frame are drawn as selected. Then mark the outer boundary lines of the UW profiles for the room element on the floor and ceiling. In our example, the rough dimension of the wall is: height: 260 cm, width: 182 cm, depth: 17.5 cm
  2. Now go four UW profiles with the tin snips to the desired length (in the example 182 cm). Do the same with the eight side rails (CW profiles). You need eight profile pieces à 260 cm (in our example the room height).

Partition with hatch and ceiling lamp: partition

step 3

Partition with hatch and ceiling lamp: lamp

Step 4
  1. As with a partition wall must also in this room element for the Soundproof the UW profiles on the ceiling and floor with a partition sealing tape be provided.
  2. Now attach the UW profiles to the floor and ceiling. In a first step they will be sent to the Pre-drilled ends and fixed with fixing dowels, Then they are separated by a distance of max. 100 cm additionally screwed. Caution: When anchoring pay attention to any laid floor heating or electrical lines!

Partition with hatch and ceiling lamp: lamp

Step 5 and 6

Partition with hatch and ceiling lamp: ceiling

Step 7
  1. Now put the CW profiles at right angles into the respective UW profiles on. Set up the entire Substructure for the plasterboard wall with a spirit level vertically out. In our example, a height of 142.5 cm and a width of 102.5 cm was chosen as the rough dimension for the opening. (maximum distance CW-profiles 625 mm)
  2. Connect all profiles to each other with crimping pliers. Begin at the endpoints first. Note: Before fastening, make sure that the profiles are aligned absolutely vertically in the perpendicular!
  3. For the support of the opening you also use UW-profiles. To do this, lengthen four profile pieces according to the selected inside dimension of the opening plus a side projection of 2 cm each. Now mark the interior measure in the middle, the Cut the leg at 45° with the shears and bend the protrusions upwards, The supports are also fastened with the crimping tool. The pliers simultaneously pierce the overlapping profiles inwards, thereby ensuring a positive connection without any further fastening means. For the lower lintel, a height of 88.75 cm (top edge) from the ground was chosen here. The distance to the upper camber depends on how far you want to hang the light ceiling.

Partition with hatch and ceiling lamp: hatch

Step 8

Partition with hatch and ceiling lamp: lamp

Step 9
  1. Because the Distances between the CW profiles not more than 62.5 cm should set, please put in the middle below or above the falls, respectively, another CW profile on. To attach these short profile pieces, proceed as with the long CW profiles.
  2. Then it goes to the Planking with plasterboard, Plasterboards are easy to work with. To cut a gypsum board, carve the cardboard box with rails and cutter or carpet knife on...

Partition with hatch and ceiling lamp: partition

Step 10

Partition with hatch and ceiling lamp: ceiling

Step 11
  1. ... then to z. B. over one Table edge to be able to break clean, The back cardboard is separated again with the cutter.
  2. To be between two together jerking gypsum boards to get a spatula, chamfer the cutting edge with the cutter on.

Partition with hatch and ceiling lamp: ceiling

Step 12

Partition with hatch and ceiling lamp: hatch

Step 13
  1. The planking and putty effort can be minimized if Planking of the room element and the light ceiling prefabricated moldings be used. These are factory-fitted with so-called V-cuts of 90° and only need to be primed and glued to the U (eg with white glue Pontal). Such moldings are available in different widths and standard lengths of 200 and 250 cm. Before these are cut to length and placed over the substructure for U glued parts, which still need be beveled with the edge planer or cutter, to get a spatula joint.
  2. Now screw the slipped moldings out of plasterboard with drywall screws at a distance of 20 cm on the framework. The lower part of the metal construction is covered with boards of the same thickness. Tip: So that the room element does not sound hollow, the intermediate fields of the stud frame can be filled with mineral wool before the planking.

Partition with hatch and ceiling lamp: profiles

Step 14

Partition with hatch and ceiling lamp: lamp

Step 15
  1. Also the sides left and right of the room element opening are covered with moldings.
  2. Finally, cover the front of the room element with plate sections.

Light ceiling suitable for the room element

For the substructure of the light ceiling (ceiling sail) you need C ceiling profiles (short CD profiles) that you like CW and UW profiles, received in the building materials trade. The planking is easy with prefabricated moldings made of plasterboard.

Partition with hatch and ceiling lamp: profiles

Step 1

Partition with hatch and ceiling lamp: profiles

step 2
  1. That's what's going on Ceiling sails of adjustable noni-hangersconsisting of upper and lower part with locking pin, and one corresponding to the opening of the space element is screwed to the opposite wall. A Noniushänger consists of a hanger, an adjusting rod and a securing clip. Dowel the first adjusting rod at a distance of max. 40 cm from the wall finishing profile to the ceiling. The further adjusting rods can then be left at a distance of max. 80 cm follow. The width between the parallel bars should not exceed 100 cm for planking with a 12.5 mm plate.
  2. Cut two CD profiles with a pair of pliers. (In our example, the length is 97.5 cm) Now hang the Noniushänger in the ceiling profiles. The profiles are available up to a length of 400 cm.

Partition with hatch and ceiling lamp: ceiling

step 3

Partition with hatch and ceiling lamp: ceiling

Step 4
  1. Set up the CD profiles using a Spirit level and the safety clips off, which are inserted through the rows of holes of the hangers and Justierstäbe. Note: After aligning the CD profiles, bend over the overhanging ends of the clips.
  2. The support profiles (also CD profiles) to which the gypsum boards are later attached can be easily connected to the two CD profiles with cross-quick connectors. In our example, the length of a supporting profile is 97.5 cm.

Partition with hatch and ceiling lamp: lamp

Step 5

Partition with hatch and ceiling lamp: lamp

Step 6
  1. After attaching the support profiles, align them centrally at the same distance from the CD base profiles, The distances between the individual support profiles should not be more than 40 cm for this type of ceiling.
  2. Finished profile construction fitted to the room element on the ceiling.

Partition with hatch and ceiling lamp: partition

Step 7

Partition with hatch and ceiling lamp: hatch

Step 8
  1. Now you begin the planking of the now prepared and assembled substructures of the ceiling sail with prefabricated moldings. When preparing the molded parts, please proceed as for the room element. Subsequently screw the moldings glued together at 10-100 cm to the support profiles with drywall screws or the wall termination profile. Finally, you plank the front of the light ceiling with plate sections.
  2. The openings for the built-in stoppers (eight in our case) can be sawed out before the planking of the ceiling sail or, as in our example, after the planking. Please note that the light spots must be arranged at a sufficient distance from the profiles. To cut out the openings, use the quick-change screwdriver with a hole saw attachment, The diameter depends on the size of the selected installation spots.

Partition with hatch and ceiling lamp: partition

Step 9

Partition with hatch and ceiling lamp: lamp

Step 10
  1. You can decoratively blind the nonius hangers with 5/3 cm aluminum angles. To do this, always glue together two angles cut to length using assembly adhesive. But pay attention to the location of your power source before doing this. Depending on the situation, the power cable for the spotlights can also be routed inside the veneer.
  2. Before you start designing the surface, consider the Outside edges of the room element provided with corner protection rails, which you cut with the tin snips to the desired length.

Partition with hatch and ceiling lamp: ceiling

Step 11

Partition with hatch and ceiling lamp: ceiling

Step 12
  1. To facilitate this operation, you can use the Secure protective rails with stainless staples before.
  2. at Fill the room element and the light ceiling with all joints, corner guards and screw holescoated with putty. Choose the widest possible spatula. To ensure that the joints no longer have any depressions after smoothing, you will need two operations, with the joint filler always having to completely dry out.

Partition with hatch and ceiling lamp: partition

Step 13

Partition with hatch and ceiling lamp: ceiling

Step 14
  1. After filling sand the mass smooth with fine sandpaper, prime the wall and make the surface as desired. You can paint the wall and the ceiling with wall paint or paper or apply roller coaster.
  2. Now install the steel blades according to the manufacturer's instructions. Connect the power cable. Have fun in your new kitchen with quality of life and inviting hospitality.

Partition with hatch and ceiling lamp: profiles

Processed rolling plaster

Partition with hatch and ceiling lamp: partition

The finished partition with hatch and light deco
  1. In our case, we have applied a roll plaster on the ceiling light. Have fun in your kitchen with more quality of life and inviting hospitality.

Similar sites

  • Build a children's bike yourself
  • Soapbox Construction Manual: Just build yourself
  • Construction manual for an individual trellis in the form of a Nintendo Gameboys
  • Tinker lampshade yourself
  • Build kennel yourself
  • Building pallet chairs - construction manual for garden armchairs made of pallets
  • Make picture frame yourself
  • Construction Manual Partybox - Build loudspeakers yourself
  • Instructions: Build your own table in Chabby-Chic
  • Shutters yourself - building instructions for shutters
  • Building instructions for birdhouses
  • Build sideboard shelf - blueprint with construction manual
  • Cushion the seat itself
  • Build practical wardrobe furniture and wall shelves
  • Build your own game tower: Spielhaus construction manual

Video Board: DIY VÄLISEINÄ | PAKUPROJEKTI OSA 15 (VANLIFE SUOMI)