Terrace with concrete slabs and paving stones


Terrace with concrete slabs and paving stones: paving

After preparing the ground for the terrace, it is time to lay the concrete slabs or paving stones. For each self-builder must know how the stones should be arranged later. Here is a layout plan helpful, with the help of which one can already see in advance whether the planned terrace pattern corresponds to the ideas. For a processing fee, you can have the area sketched by the customer transferred to a laying pattern by a draftsman when purchasing the necessary materials.

It should It also becomes clear which materials should come to rest. For example, those who want to combine concrete slabs with natural stones can have problems. Because of the different construction heights (natural stone paving 5 to 8 cm, concrete slabs 3 to 5 cm), the substrate must be adapted accordingly.

As materials for paving the terrace one needs apart from the terrace slabs or stones also a Feinsplitt-, sand or mortar mixture for the bedding and a guideline, a long wooden board and a rubber mallet. In addition, grit, sand or quartz sand as well as a broom and water are needed to sludge the terrace surface.

Terrace with concrete slabs and paving stones: paving

How to create the bedding?

For the laying of a stone terrace, a bedding is created, which usually consists of a fine split, sand or mortar mixture. In a bonded version, plaster paving mortar, laying sludge and joint mortar are required for paving, which ensures lasting stability. For that can washed sand mixed with commercial cement in the ratio 3: 1 become.

Terrace with concrete slabs and paving stones: concrete

In an unbound design, a crushed sand grit mixture with a grain size of 0 to 5 mm serves as a leveling layer. This should be 0.5 to 1 cm higher than the finished terrace area minus the thickness of the terrace covering, so that after the compaction, the terrace surface and border are flush.

The crushed grit mixture or the dry mortar are in a layer of 3 to 8 cm thickness loosely spread over the surface and smoothed.

Terrace with concrete slabs and paving stones: slabs

One should Make sure that there are no stones or mortar residues in the bedding. To remove the surface can be used metal tubes, so-called gauges, which are embedded in height and gradient accordingly and on which the bedding is removed with a longer wooden board.

Subsequently, the Removed metal tubes and filled the remaining grooves. The terrace ground should not be entered after pulling it off. However, if the area is so large that straight-line laying becomes more difficult, it is advisable to work in sections of approx. 1.5 to 2 m.

How to pave a terrace?

Terrace with concrete slabs and paving stones: concrete

It is advisable when paving with concrete blocks or paving stones to start on a straight side like a house facade. In the case of larger terraces, it is also advisable to work in sections and to stretch the cords from the façade at right angles at a distance of approx. 1.5 m. This achieves a straight butt joint layer.

In addition, it is important for bound executions that one Space for an expansion joint at the edges or internals, which should have a width of about 4 mm. The first concrete slab is aligned along the tensioned guideline and pushed to below the door or window profile. It should be ensured that these and all subsequent plates are aligned according to the previously selected gradient from the house to the garden with a rubber.

Terrace with concrete slabs and paving stones: terrace

A spirit level can be used to control the course. One should also make sure that the Joints free of mortar and sand stay and the individual rows are always passed through clean. It can help cross joints, which ensure a gap of 3 to 5 mm.

When laying paving stones and pavers is also a usually narrow joint spacing between 3 and 5 mm left, which is filled after about four rows with crushed sand. The paving stones are installed "overhead".

Terrace with concrete slabs and paving stones: concrete

To get a color balanced terrace area, one should mix the stones from several packages and different layers. This not only applies to paving stones and clinker, but also to concrete slabs. As a material from the natural products of gravel, sand and cement, concrete is subject to natural color variations. Although high-quality iron epoxy paints and colourfast hard rock splinters are used, fluctuations can occur between different deliveries.

How to create a terrace with pattern?

Terrace with concrete slabs and paving stones: concrete

For beginners, it is advisable to do without elaborate patterns and lay the terrace of concrete slabs or paving stones only in simple associations or straight lanes.

Nevertheless, it is possible to lay a terrace of differently colored concrete slabs and these to make it more interesting with design paving stones.

Terrace with concrete slabs and paving stones: slabs

Terrace with concrete slabs and paving stones: stones

Terrace with concrete slabs and paving stones: stones

For example, you can use a different colored concrete block for the banding and the patio slabs with small inlays - z. B. stainless steel - loosen up. These are only knocked loose into the bedding after the first plates have been laid. Missing passages can also be easily made with a water-cooled stone saw or an angle grinder. You can also cut terrace tiles with a stonecracker.

Terrace with concrete slabs and paving stones: concrete

Terrace with concrete slabs and paving stones: slabs

Terrace with concrete slabs and paving stones: paving

The paving of the terrace should be done very carefully. Therefore you should too again and again take the spirit level and control the slope. The work works best if you have at least one helper with whom you can finish the terrace in teamwork quickly and accurately.

Terrace with concrete slabs and paving stones: terrace

Terrace with concrete slabs and paving stones: terrace

How to have a terrace?

Terrace with concrete slabs and paving stones: concrete

Terrace with concrete slabs and paving stones: slabs

Terrace with concrete slabs and paving stones: slabs

After paving the terrace takes place the sludging of the surfaceto close the joints of the decking. When laying concrete slabs, it is best to use quartz or silver sand, which will easily penetrate any joint. For an area of ​​25 square meters, about three sands of sand are needed. This is swept with a broom in the joints and then wet with a garden hose. This gives the terrace surface its composite effect and load capacity. Finally, the remaining sand is turned away.

Terrace with concrete slabs and paving stones: slabs

When laying paving stones and pavers, the joints are filled first with dry crushed sand with a grain size of 0 to 2 mm or with grit with a grain size of 1 to 3 mm. The filled plaster ceiling must - unlike concrete slabs - then be compacted best with a vibrating plate with plate slide. Only after shaking the joints are completely filled by immersion of sand, slipped the joint sand with a water hose and cleaned the terrace surface of the sand residue.

What remains is a clean, creatively playful or calm depending on the laying pattern Paving with a very high life expectancy. If you want to promote the longevity of the plaster bandage even more, so you should consider the alternative method paving stones with grout into consideration.

Similar sites

  • Lay outdoor tiles and patio tiles
  • Crafting templates and craft arches
  • Tinker folding cards
  • garage door types
  • Design the terrace - instructions
  • coloring
  • Clean joints in the bathroom and garden properly
  • Prepare underground for terrace
  • Coloring pages and coloring pages
  • Tile the terrace
  • Correctly lay a natural stone terrace


Video Board: How to Install Concrete Flag/Block Paving Flexibly | Commercial Paving | Marshalls